Pvc & Application - Yıldız Yapı Sistemleri

Component on floor to be care: The applied floor must be smooth. If there is not because of the thickness of products 2 -4 mm ruin in floor will be seen. The floor like this must be smoothed by self_leveling. If there is a wood in appliying area and over this if there is any rough thing which seen over must be utterly eradicated. Because self-leveling can not be over wood

The Appliying area Conditions: Every manufactured goods must be ended before pvc-Linoleum covering. In these manufacture installation door assembly paint and white wash heating system mezzanine floor etc. Thus after lay down the covering would not be damage. End of this application the covering floor with Pvc-linoelum must be cleaned. This area must be closed and the heat must not exceed 18 degree Pvc – Linoelum roller should be in upright position.

Self- Leveling and Application : If the place covering with pvc and linoleum are not smooth you should make self-leveling. These self-leveling get usud between 0.5 mm and 60,0 mm ruin to recover.( Look at henkel self-leveling) so this self-leveling used to get smooth floor. Self- leveling is mixing with water a known rate and appliying with the help trowel. This alum does automatically level. No distance altitude on the floor. Water bases self-leveling should be controlled before the pvc- linoleum application and should be looked. If there is moisture. If there is any place not dry application sholud not be done. Otherwise during time can be seen pimple on the floor.

Flat Application: First the measure of flooring takes. Due to measure is cutting from the rollers more than 5-10 cm then with the help of crested troewl the sticky applies the whole area. There should not be any stone soil or any sticky over the floor. While the sticky comes to the right consistency done the sticky operation. The edge of cutting product lean againts the wall and the other tip spread over in a form over the wall. And then the furter part is cutten by the help of borbedknife. After the application of sticky operation is completed the cylinder goes over it. After the product puts on the sticky the patches cuts according to measure.

Reflexive Application: With the help of pencil or ruled paper is marked the wanted highest position to the wall. By the marked place is spreaded the henkel K-12 or henkel patex sticky. Special plaster cap and pillow sticks to the wall. Between pvc floor and wall bended lika a equal radius. The pvc is heated and pressed tightly to the wall. The lay pressed towards to the edge. The patched place is 45 grade / degree the further distance is cut under the part of edge and hollowed out. The patches combined with hot weld after the cooling the plenty is taken. In the out edge bended the pvc towards to the wall and approximately is cut the angle of 45 degree. The patch piece is cut like triangle. Back of this piece is opened a pipet he half of it is thickness. The patch lightly heated and puts own itis place. Linoelum is turned to the wall only with the special apparatus.

Tile Application: It is covering like straight application above. Usually the tile dimensions are 60,8 x 60,8 or 61 x 61 cm. A some kind of products have 50 x 50 cm tile dimensions. After the pvc sticked on the floor made the hot weld to the patches.

Welt Operation: The patch place adjusted not so near to another. With the seam machine opened 3,5 cm width canal in the patch place. The opened canals must be sweep away the cable attached to the machine and with the action to the back whole seam pulled. After this stil the weld is hot the plenty is taken. After the weld cooling the smoothing operation is make.

When we look at the sale of the floor covering first the choice is according to price and so thinking that we are making a cheap covering. And the risks after this do not bear in mind. Clean and care high cost and not trough the technical operation products after one and two years the same level like the first cost. Be important is right products for right place. Floor covering total cost % 10 percent of cleaning cost according to 20 years usage existence. With PUR powerful floor covering posibble new cleaning method and low cleaning cost.

PUR ( Polyurethane ) providing clean operation when the production add to floor covering by helped temperature a plastic. Because of PUR do not get trough water on top of the floor covering. However PUR rised surface by dry sweeping-brush and preventing polish cost. You can use this products a long time no need anything chemical product.

The dirty % 80 percent with feet on the flooring. The dirty % 90 percent be able to preventing by the right doormat. Even low clean and long existence.

Diffrent save method is for flooring covering table, chair, and seat foot’s must be quality. Due to product never damage.

However detergent and water will be lower even cost and will be keep ecological balanced. Water lower each other friction and easy cleaned. This is advantage not breath chemical for your healt.

Mop the floor before surely must be clean dirty and dusty by vacuum-cleaning
It is mop the floor must be everyday. This method is best. When the make mop the floor moisture must not be water on the floor.
The other method is spray cleaning for local cleaning.
It is wet mop the floor method for use very dirty condition. Mat must not be so wet. After mop the floor must be handcart.
Optionel use brush-machine with red pod for cleaning. During the operation must be low speed ( 150 -200 ) rpm
It must be wet vacuum after the brushing for remain water on floor.
If your floor covering homogenous and done friction must be dry high speed brushing. Machine speed must be 1000 rpm in this method. In this application red pad good results
Posibility even brushing and vacuum machine can be used. During in this application can be use brush and pad.
If the occured local dirties can be use notr detergent by the white and red pad. After the operation surely cleaning with pure water.

More than necessery when use to so much sucking detergent on the floor. Floor covering‘s wiew, brightness can be deformation and for cleaning getting harder. However aceton, oil, hydrocarbon, thinner, wax materials can be damage to pvc floor covering. Lime water can be reason a layer on the floor covering. In this condition must be include PH detergent for the cleaning lime remain.

On the Floor Covering Spots:

Forniture’s foot and chairs’s foot included bad chamical. However you must be clean to scrope a surface in the direction of flooring for dirties. Meanwhile could be essantial dry brushing. However could be sticky dirties. Have a two steps for cleaning. The first wiping with wet towel second cleaning pure water. It must be by hand control.

Pads it takes colours according to thickness and usage. It must be use red pad for PUR products. It must be use white or beige pad or microfiber for heterogenous pvc. Notice is first machine must be work low speed. If necessery to higher power. Brushes give a good results in the rough products. In the embossed floor covering products also making brush. Notice is when the put on brush to machine same time under the brush put on fibrous pad.